Panel 1440 x 900

NAND load lzhs header from SysImgB(part:3) to dram(0x2fe6a00), size=2048
DTV>
oot-
DRAM Channel A Calibration.
Byte 0 : DQS(7 ~ 37), Size 31, Set 20.
Byte 1 : DQS(0 ~ 34), Size 35, Set 15.
Byte 2 : DQS(-1 ~ 31), Size 33, Set 13.
Byte 3 : DQS(-4 ~ 29), Size 34, Set 10.
DRAM A Size = 256 Mbytes.
oot
Start Pmain
0x00004000
NID=0x9500f1ec
LZHS addr:0x00100040
LZHS size:0x00095b70
LZHS checksum:0x00000029
oot
Start Lmain

MT5365 Boot Loader v0.9
[PCMCIA]Set PCMCIA Access IF : SPI
SPIHW_Init ----- Set SPI PinMux
SPI dummy delay:0x10
External CI Version : MT5135
Output clock from main chip.
PCMCIA Reset Demod GPIO=35, 0->1
SPI_SetPll(), spi clock: 27 Mhz
External IC Initilization done
MUSB none SoftReset 0x29424 = 0x01030000.
MUSB pBase = 0xF0029000 init ok.
MUSB none SoftReset 0x29424 = 0x01030000.
MUSB pBase = 0xF002E000 init ok.
Boot reason: A/C power on!!-------------use external edid, disable internal edid------------------
SIF_Master0: new design
SIF_Master1: old design
Boot reason: A/C power on!!T8032 init A/C on case loader stage...
Load T8032 FW (addr: 0x 2d37f88, size: 24576)success!!
T8032 FW version: 17
T8032 change to loader stage...
LDR_FlashCopy 0xf010 0x34a00 0x80
Switch NAND pinmux
Detect NAND flash ID: 0x9500F1EC
Detect SS K9F1G08U0B/C NAND flash(SLC): 128MB
NAND_BDM_Mount: Partid=0, offset=0x0, size=0x40000
[BDM] Partition: 0, Bad Block Count: 2
BDM too many bad block in partition 0
NANDPART_Read ASSERT2: Partition ID = 0, Offset = 0x20000

Do USB upgrade

No USB device.
USB upgrade stop
Boot reason: A/C power on!!Boot reason: A/C power on!![PDWNC]PDWNC_TPV_DetermineNextState : u4Event = 0x6
PDWNC_TPV_DetermineNextState : u4Current = 1
PDWNC_TPV_DetermineNextState : system booting
[PDWNC] Virgin Mode Status : 0x1, Offset :0xFF
PDWNC_TPV_DetermineNextState : event = PDWNC_POWER_DOWN_AC_POWER
Current = 0x1, Event = 0x6, Next = 0x1
Wakeup keypad array = 3
Boot reason: A/C power on!![PDWNC]PDWNC_ReadWakeupReason = 0x6
[PDWNC]Enter normal mode, LED changes to normal
PDWNC_TPV_EnterNextState : u4Next = 0x1
Boot reason: A/C power on!!
A_Mute GPIO=11 release
AMP mute GPIO=cb release
Reset Demod GPIO=23, 0->1
Display 0x02d9e67c background:0x00000000
2 bytes panel index is : 255 (0x  ff)
No valid index found from EEPROM
[LVDS] DVOPLL init control word only
[LVDS] VOPLL Initialize successful !
LODFP.
Boot reason: A/C power on!!---------- Panel[  2] PANEL_CMO_19_A1 1440x900 ----------
PixelClk[Max=112000000, 60Hz=88807193, 50Hz=74080000, Min=72979200]
HTotal[Max=1919, 60Hz=1599, 50Hz=1599, Min=1499] HSyncLen[60Hz=159, 50Hz=159]
VTotal[Max=1049, 60Hz=925, 50Hz=925, Min=904] VClk[Max=75, Min=56]
HSyncWidth=5, VSyncWidth=3, HPosition60Hz=0x800, HPosition50Hz=0x800, VPosition=1008
LVDS_NS, LVDS_ODD_SW_OFF, DUAL_PORT, DISP_24BIT
WFB_PANEL_RESET_OFF, PWM_HIGH_PANEL_BRIGHT
3D_POLARIZED
 Backlight[High=0xff, Middle=0x70, Low=0x0]
DimFreq60Hz=0, DimFreq50Hz=0
Delay[LvdsOn=10, BacklightOn=450, BacklightOff=90, LvdsOff=10]
MaxOverscan=50

Current panel setting is PANEL_CMO_19_A1
Backlight gpio=25, turn on value=0, LVDS gpio=16, turn on value=1
Pixel Shift=0 (1440 x 900)
LDR_OsdDisplay(13, 0x02d42110, 400, 100)
Color:13 BmpAddr:0x02d42110 Width:400 Height:100
OSD_SetTVEOut: 1
 osd flip en
 osd mirror en
Panel 1440 x 900

NAND load lzhs header from SysImgA(part:1) to dram(0x2fe6a00), size=2048
NAND_BDM_Mount: Partid=1, offset=0x40000, size=0x1e00000
[BDM] Partition: 1, Bad Block Count: 240
BDM too many bad block in partition 1
NANDPART_Read ASSERT2: Partition ID = 1, Offset = 0x0
No valid image found! 0x02fe6a00: 0x03d6c191 0x35333958

Try the other image, DTVCFG_FLAG2_IMAGE_BANK=1

NAND load lzhs header from SysImgB(part:3) to dram(0x2fe6a00), size=2048
NAND_BDM_Mount: Partid=3, offset=0x1e40000, size=0x1e00000
[BDM] Partition: 3, Bad Block Count: 240
BDM too many bad block in partition 3
NANDPART_Read ASSERT2: Partition ID = 3, Offset = 0x0
No valid image found! 0x02fe6a00: 0x03d6c191 0x35333958

Force USB upgrade


No USB device.
USB upgrade stop

DTV>