=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2016.12.17 13:02:46 =~=~=~=~=~=~=~=~=~=~=~= Boot- DRAM Channel A Calibration. Byte 0 : Gating(2 ~ 77), Size=76, Mid=41, Set=41. Byte 1 : Gating(2 ~ 72), Size=71, Mid=39, Set=39. Byte 2 : Gating(2 ~ 77), Size=76, Mid=41, Set=41. Byte 3 : Gating(2 ~ 77), Size=76, Mid=41, Set=41. Byte 0 : DQS(7 ~ 39), Size 33, Set 23. Byte 1 : DQS(8 ~ 35), Size 28, Set 21. Byte 2 : DQS(6 ~ 38), Size 33, Set 22. Byte 3 : DQS(10 ~ 33), Size 24, Set 21. DRAM A Size = 1024 Mbytes. Boot Start Pmain 0x0000a000 Nand boot NID=0x9510dcec LZHS addr:0x00100040 LZHS size:0x001f7ee0 LZHS checksum:0x0000006f Boot Start Lmain MT5880 Boot Loader v0.11 Boot reason: A/C power on!! [PDWNC] PDWNC_PHILIPS_ReadWakeupReason: 6 (status 0x0) SIF_Master0: new design -------------use external edid, disable internal edid------------------ IR DATA register : 0x 0 T8032 init A/C on case loader stage... Load T8032 FW (addr: 0x d44a38, size: 24576)success!! T8032 FW version: 8 T8032 change to loader stage... LDR_FlashCopy 0xf010 0x72f00 0x80 Detect NAND flash ID: 0x9510DCEC Detect SS K9F4G08U0B/D NAND flash(SLC): 512MB NAND_BDM_Mount: Partid=0, offset=0x0, size=0x200000 NAND_BDM_Mount: Partid: 0, Total Block Count: 16, Bad Block Count: 0 1st MAC in EEP is valid (1c:5a:6b:1a:82:99) 1st : (1c:5a:6b:1a:82:99) 2nd : (1c:5a:6b:1a:82:99) [PDWNC] Current state : 0x1 [PDWNC]PDWNC_PHILIPS_DetermineNextState : u4Event = 0x6 PDWNC_PHILIPS_DetermineNextState : u4Current = 1 PDWNC_PHILIPS_DetermineNextState : system booting PDWNC_PHILIPS_DetermineNextState : event = PDWNC_POWER_DOWN_AC_POWER Read EEPROM OK at PDWNC_PHILIPS_GetLoungeMode PDWNC_PHILIPS_DetermineNextState : Lounge mode = 0 Current = 0x1, Event = 0x6, Next = 0x1 [PDWNC] PDWNC_PHILIPS_EnterNextState : u4Next = 0x1 [PDWNC]PDWNC_ReadWakeupReason = 0x6 [PDWNC]Enter normal mode, LED changes to normal PDWNC_Init USB0: Set GPIO63 = 1. USB1: Set GPIO64 = 1. Display 0x00efd4c0 background:0x00000000 Find panel index 194 from EEPROM OSD_SetPlaneSwitchOrder[0,1,2],Switch[1,2,3] ---------- [SA7] vErrorHandleInit ---------- [SA7] Error handling init [SA7] PANEL_GetPanelWidth=0x780, PANEL_GetPanelHeight=0x438 , wDrvGetOutputHTotal=0x898 , wDrvGetOutputVTotal=0x465 [SA7] PANEL_GetHTotalMax=0xa60, PANEL_GetHTotalMin=0x870, PANEL_GetVTotalMax=0x5c8, PANEL_GetVTotalMin=0x442 [SA7] PANEL_GetPixelClkMax=164000000, PANEL_GetPixelClkMin=122000000 [SA7] PANEL_GetPixelClk60Hz = 0x8dab561 ---------- [SA7] vErrorHandleSetByTiming ---------- [SA7] u2HSyncWidth=260, u2HSyncStart=1930, u2VSyncWidth=26, u2VSyncStart=1094 ---------- [SA7] vErrorHandleSetByTiming end---------- ---------- [SA7] vErrorHandleSetByPanel end---------- [SA7] vDDDSInit ---------- [SA7] vErrorHandleSetByTiming ---------- [SA7] u2HSyncWidth=30, u2HSyncStart=1936, u2VSyncWidth=3, u2VSyncStart=1119 ---------- [SA7] vErrorHandleSetByTiming end---------- vDrvSetOCLKClockSchemaInit. [SA7] _fgVopllUseDDDS = True [LVDS] VOPLL Initialize successful ! LDR_OsdDisplay(14, 0x00d64ac0, 1280, 291) Color:14 BmpAddr:0x00d64ac0 Width:1280 Height:291 OSD_Base_SetHStart[h=0x2e7,v=0xc] Panel 1920 x 1080 *************u4BmpPitch=5120****************** Do USB upgrade USB: Vbus turn up time = 1600 ms, Max =0 ms. USB-0: insert. USB-0: ClassCode= 0x9, u4Diff=120 ms. FIND_CLASS_HUB. HUB No USB Medium on Hub. USB upgrade stop Flash load lzhs header from 0x80000 to dram(0x1526290), size=2048 Decompression uboot to 0x00800000... Flash load image from 0x80000 to dram(0x1526290), size=0x3fdf8 NAND_BDM_Mount: Partid=4, offset=0x300000, size=0x400000 NAND_BDM_Mount: Partid: 4, Total Block Count: 32, Bad Block Count: 0 Flash load tz from 0x20dbff(kernel) to dram(0x3f200000), size=0x2aa5e secure boot ok secure boot ok Starting image... ÿ U-Boot 2011.12.12 (Dec 15 2012 - 11:02:19) DRAM: 741.3 MiB WARNING: Caches not enabled NAND: Detect NAND flash ID: 0x9510DCEC Detect SS K9F4G08U0B/D NAND flash: 512MB 512 MiB 0.0.0.0 In: serial Out: serial Err: serial Boot from kernelA and rootfsA(partition 6) Net: Net Initialization Skipped No ethernet found. Hit any key to stop autoboot: 0 Partition rootfsA defined at mtdparts: ID:6, Offset:0x00000000, Size:0x00b00000 Loader succeeded in signature verification ## Booting kernel from Legacy Image at 00007fc0 ... XIP Kernel Image ... OK OK Starting kernel ... TZ Heap: start=0x3FA5B900, end=0x40000000 TZ dram: start=0x3F000000, end=0x40000000 [ 0.000000] timekeeping_init done INIT: version 2.86 booting Loading /etc/profile... Start readahead /etc/readahead_early Start readahead /etc/readahead Running rc.local... net.ipv4.tcp_window_scaling = 6 /3rd/hbbtv/lib:/3rd/mhp/lib:/3rd/yahoo_widget:/3rd/yahoo_widget/lib:/3rd/opera/3rdpartylibs:/basic:/basic/lib:/3rd/lib:/3rd/libiconv/libiconv-1.13.1/lib:/3rd/samba/samba-3.5.0/lib::/basic:/basic/lib:/basic/lib/alsa-lib-1.0.24.1/lib:/3rd/lib:/3rd/AdobeAIR/stagecraft-2.5.1.340/lib:/3rd/flash_lite/lib:/3rd/lib/iconv/lib:/3rd/samba/lib:/3rd/netflix/flash-app/lib:/3rd/gtkdfb/lib:/3rd/libxml2/libxml2-2.7.8/lib:/3rd/mtal:/3rd_rw/nettv:/3rd/nettv:/basic:/3rd/wpa_supplicant/atheros tty_mngr_init Input: CLI : switch to mw_cli. : switch to app_man. : switch to app_man. **********DirectFBInit() commandline read: app_man ~~~~~~~~~~~~~~~~~~~~~~~~~~| DirectFB 1.4.0 |~~~~~~~~~~~~~~ (c) 2001-2009 The world wide DirectFB Open Source Community (c) 2000-2004 Convergence (integrated media) GmbH ---------------------------------------------------------------- input thread's parent pid is 501 tid is 501 [DirectFB]: Wait to Init IR...! dfb_set_cursor_border [0,0,1280,0] input thread pid is 501 tid is 511 original scheduler policy 0 scheduler nice 0 original child scheduler policy 0 prio 0 new child scheduler policy 2 prio 99 Start to wait IR event... [dtv_app_mtk]>drv_init as 0x39 model [dtv_app_mtk]>drv_init as EU model [dtv_app_mtk]>HDMI fast booting init... [ 10.580925] NAND_SDM_Mount: Partid=15, offset=0x1d680000, size=0x2980000 [dtv_app_mtk]> [dtv_app_mtk]>TVD MsgCtrl: NRL:60/40, PER:100/90 [dtv_app_mtk]>x_drv_init end!! [dtv_app_mtk]>[ FakeDM ] Init... [dtv_app_mtk]> [FakeDM] Init FM... [dtv_app_mtk]> /dev is created./mnt is already existed. That is OK. [dtv_app_mtk]> /mnt/usb is created.[FakeDM] FM inited... [dtv_app_mtk]> [FakeDM] Init SMB... [dtv_app_mtk]> [FakeDM] SMB inited... [dtv_app_mtk]> [FakeDM] do coldboot start... [dtv_app_mtk]> [DM] _dm_open_dev_thread: entered [dtv_app_mtk]> [DM] _dm_nfy_req_thread enter [dtv_app_mtk]> [DM] _dm_nfy_req_thread get_nl_sock:24 [dtv_app_mtk]> [DM] _dm_cb_msg_thread enter [dtv_app_mtk]> [DM] usbfs mounted. [dtv_app_mtk]> [FakeDM] do coldboot end!!! [dtv_app_mtk]> Init chip_spec_init!!!!! [dtv_app_mtk]> EEPROM size is 0x4000. [dtv_app_mtk]> {CI_glue}:ci_eng_init [dtv_app_mtk]> {CI_glue}- expect PROD key [dtv_app_mtk]> {CI_glue}- c[1] [dtv_app_mtk]> [ACFG_CUSTOM] acfg_custom_get_svl_tsl_dual_bank ui1_g_svl_tsl_dual_bank == DUAL_BANK_SVL_TSL_INVALID and get form plf is 255 [dtv_app_mtk]> 88888888888888 PHYSICAL_Init() entered 888888888888888 [dtv_app_mtk]> 88888888888888 ITC_Init() entered 888888888888888 [dtv_app_mtk]> 88888888888888 PHYS_DRVOpen() entered 888888888888888 [dtv_app_mtk]> 88888888888888 STB_CIOpen() entered 888888888888888 [dtv_app_mtk]> ~~~~~~~~httpc_client_init sucessfully~~~~~~~~~~~ [dtv_app_mtk]> [HTTP FM]~~~~~~~~httpc_fm_init sucessfully~~~~~~~~~~~ [dtv_app_mtk]> [ACFG_CUSTOM] acfg_custom_get_svl_tsl_dual_bank Line 9210 [dtv_app_mtk]> [ACFG_CUSTOM] acfg_custom_get_svl_tsl_dual_bank: MAIN [dtv_app_mtk]> 88888888888888 STB_CIOpen() ended 888888888888888 [dtv_app_mtk]> {CI}CI_RegInterrupt_nfy [dtv_app_mtk]> 88888888888888 PHYS_DRVOpen() entered 888888888888888 [dtv_app_mtk]> {CDB} Loading metadata (version 7) [dtv_app_mtk]> {CDB} Loading metadata (version 7) [dtv_app_mtk]> {CDB} Loading metadata (version 7) [dtv_app_mtk]> {CDB} Loading metadata (version 7) [dtv_app_mtk]> {CDB} Loading metadata (version 7) [dtv_app_mtk]> {CDB} Loading metadata (version 7) [dtv_app_mtk]> {CDB} Loading metadata (version 7) [dtv_app_mtk]> [dtv_app_mtk]> ~~~~~~~~~~~~~~~~~~~~~~~~~~| DirectFB 1.4.0 |~~~~~~~~~~~~~~ [dtv_app_mtk]> (c) 2001-2009 The world wide DirectFB Open Source Community [dtv_app_mtk]> (c) 2000-2004 Convergence (integrated media) GmbH [dtv_app_mtk]> ---------------------------------------------------------------- [dtv_app_mtk]> [dtv_app_mtk]>dfb_set_cursor_border [0,0,1280,0] window size: 0 stacking [0x0], layer_id [0] [dtv_app_mtk]> MHEG5 TPS start to setup [dtv_app_mtk]> [MHEG5_NVM]rw root path = /3rd_rw [dtv_app_mtk]> MHEG5 TPS setup failed to create dir(-6) [dtv_app_mtk]> EEPROM size is 0x70. [dtv_app_mtk]> [dtv_app_mtk]> [dtv_app_mtk]> x_wifi_cli_init~~~ [dtv_app_mtk]> [dtv_app_mtk]> [dtv_app_mtk]> Rec_util_thread:buffer addr 0x00003d79b000,size 0x380000 [dtv_app_mtk]> {HBBTV_DSMCC} Init HBBTV DSMCC [dtv_app_mtk]> EEPROM size is 0x70. [dtv_app_mtk]> [SYS_CONFIG] Err: read 2 data failed:0 [dtv_app_mtk]> ===================== [dtv_app_mtk]> channel id:(262272), svl rec id:(1), channel id in rec:(262272), brdcst type:(1) [dtv_app_mtk]> ===================== [dtv_app_mtk]> [dtv_app_mtk]> channel info: svl_id(262272), channel_id(262272) [dtv_app_mtk]> [SYS_CONFIG] Err: read 2 data failed:0 [dtv_app_mtk]> {DT} Real Time Clock is available on this system. [dtv_app_mtk]> reason: 0x00000006 - 0x00000000 [dtv_app_mtk]> wakeup reason = 6 [dtv_app_mtk]> EEPROM size is 0x35b0. [dtv_app_mtk]> EEPROM size is 0x4000. [dtv_app_mtk]> reason: 0x00000006 - 0x00000000 [dtv_app_mtk]>[OT][_acfg_ch_lst_load_p1][718]: e_wakeup_reason = 6. [dtv_app_mtk]> {CDB} Loading metadata (version 7) [dtv_app_mtk]> {CDB} Loading metadata (version 7) [dtv_app_mtk]> {CDB} Loading metadata (version 7) [dtv_app_mtk]> {CDB} Loading metadata (version 7) [dtv_app_mtk]> {CDB} Loading metadata (version 7) [dtv_app_mtk]> {CDB} Loading metadata (version 7) [dtv_app_mtk]> **********DirectFBInit() [dtv_app_mtk]>SC_FCT_0: sched_getparam 492 error -1 [dtv_app_mtk]>SC_FCT_0: sched_getparam 494 error -1 [dtv_app_mtk]>MTDRVCUST_BootupCheck() fail, ret=-5 [dtv_app_mtk]>[_TunerNotifyInitThread:229] Register Tuner component Fail! [dtv_app_mtk]>[_TunerNotifyTunerProc:266] Register Tuner component excl list Fail! [dtv_app_mtk]>[_TunerNotifyTunerProc:266] Register Tuner component excl list Fail! [dtv_app_mtk]>[_TunerNotifyInitThread:229] Register Tuner component Fail! [dtv_app_mtk]>[_TunerNotifyInitThread:229] Register Tuner component Fail! [dtv_app_mtk]>[_TunerNotifyInitThread:229] Register Tuner component Fail! [dtv_app_mtk]>[_TunerNotifyTunerProc:266] Register Tuner component excl list Fail! [dtv_app_mtk]>[_TunerNotifyTunerProc:266] Register Tuner component excl list Fail! [dtv_app_mtk]>[_TunerNotifyTunerProc:266] Register Tuner component excl list Fail! [dtv_app_mtk]>[MTCI0] MTCI_Init : 0 [dtv_app_mtk]>**********DirectFBInit() [dtv_app_mtk]>[* GL DFB *] Create plane (ON layer) :1014559 [dtv_app_mtk]>[* GL DFB *] Create plane (ON window (Shared)) :1014558 [dtv_app_mtk]>{IOM} UART thread inited. [dtv_app_mtk]>MTDRVCUST_dcustom_misc_set() fail, ret=-1 [dtv_app_mtk]>x_dbg_abort rm_op.c:4011 code:0x49000b