oot- DRAM Channel A Calibration. Byte 0 : DQS(7 ~ 37), Size 31, Set 20. Byte 1 : DQS(0 ~ 32), Size 33, Set 14. Byte 2 : DQS(0 ~ 36), Size 37, Set 16. Byte 3 : DQS(-2 ~ 30), Size 33, Set 12. DRAM A Size = 128 Mbytes. oot Start Pmain 0x00004000 NID=0x1d00f1ad LZHS addr:0x00100040 LZHS size:0x00095ca0 LZHS checksum:0x000000fb oot Start Lmain MT5365 Boot Loader v0.9 [PCMCIA]Set PCMCIA Access IF : SPI SPIHW_Init ----- Set SPI PinMux SPI dummy delay:0x10 External CI Version : MT5135 Output clock from main chip. PCMCIA Reset Demod GPIO=35, 0->1 SPI_SetPll(), spi clock: 27 Mhz External CI is dead ! Version Code : 0x0 ExternalIc_Init: Daughter board is not connected. PCMCIA_GPIO_Init: Daughter board is not connected. MUSB none SoftReset 0x29424 = 0x01030000. MUSB pBase = 0xF0029000 init ok. MUSB none SoftReset 0x29424 = 0x01030000. MUSB pBase = 0xF002E000 init ok. Boot reason: A/C power on!!-------------use external edid, disable internal edid------------------ SIF_Master0: new design SIF_Master1: old design Boot reason: A/C power on!!T8032 init A/C on case loader stage... Load T8032 FW (addr: 0x 2d38024, size: 24576)success!! T8032 FW version: 17 T8032 change to loader stage... LDR_FlashCopy 0xf010 0x34b00 0x80 Switch NAND pinmux Detect NAND flash ID: 0x1D00F1AD Detect HY27U1G8F2BTR NAND flash(SLC): 128MB NAND_BDM_Mount: Partid=0, offset=0x0, size=0x40000 [BDM] Partition: 0, Bad Block Count: 0 Do USB upgrade Wait USB medium to be mounted... USB Medium on Device, Time = 2454 ms. USB block size = 512 bytes. Read Dir Entries: 0 File Name: upgrade.pkg file_name = upgrade.pkg - prefix = upgrade - check prefix = PS_2K11_NU_BER_DL Match file name not found, use the default one: upgrade.pkg Upgrade File Name: upgrade.pkg Upgrade File Size: 34185232 Bytes Display 0x02d9e7ac Idx:1 BG:0x00eeeeee 2 bytes panel index is : 129 (0x 81) Find panel index 129 from EEPROM [LVDS] DVOPLL init control word only [MLVDS]_u1TconMode=0x1 [MLVDS]TCLK_PCLK_RATION_NUM=0x1 [MLVDS]TCLK_PCLK_RATION_DEN=0x1 [MLVDS]u2Oclk_target=0x2bda [MLVDS]u2Oclk2_target=0x2bda [MLVDS]0x0D1a0=0xe24e820 [MLVDS]0x0D1a4=0xec8106e [LVDS] VOPLL Initialize successful ! LODFP. TG on phase 0: 0xc No cust minilvds setting for this panel 129 tg init Tcon reg flashing 92 counts, 4 / 12 Tcon Gamma init Program Tcon Gamma dacs 0 counts, 0 / 12 TG on phase 1: 0xc TG on phase 3: 0xffff Boot reason: A/C power on!!---------- Panel[129] PANEL_MLVDSV6GIP60_LC320EUG_LDN1 1920x1080 ---------- PixelClk[Max=154000000, 60Hz=148500000, 50Hz=148500000, Min=140000000] HTotal[Max=2399, 60Hz=2199, 50Hz=2199, Min=2119] HSyncLen[60Hz=279, 50Hz=279] VTotal[Max=1379, 60Hz=1124, 50Hz=1349, Min=1091] VClk[Max=63, Min=47] HSyncWidth=30, VSyncWidth=5, HPosition60Hz=0x396, HPosition50Hz=0x396, VPosition=1016 LVDS_NS, LVDS_ODD_SW_OFF, DUAL_PORT, DISP_30BIT, WFB_PANEL_RESET_OFF, PWM_LOW_PANEL_BRIGHT 3D_POLARIZED Backlight[High=0x0, Middle=0x0, Low=0x0] DimFreq60Hz=150, DimFreq50Hz=150 Delay[LvdsOn=20, BacklightOn=300, BacklightOff=300, LvdsOff=20] MaxOverscan=30 Current panel setting is PANEL_MLVDSV6GIP60_LC320EUG_LDN1 Backlight gpio=25, turn on value=0, LVDS gpio=16, turn on value=1 Pixel Shift=0 (1920 x 1080) Color:13 BmpAddr:0x02d55a80 Width:448 Height:60 OSD_SetTVEOut: 1 osd flip en osd mirror en Panel 1920 x 1080 LDR_OsdDisplay(13, 0x02d55a80, 448, 60) return 0 u4NANDFlashBlockSize:20000 Use internal integrity check API open File = /mnt/usb_0/upgrade.pkg open File = /mnt/usb_0/upgrade.pkg Encrypted header: 87 5e 64 87 30 c0 d2 c5 4b 87 d4 55 54 4f 85 68 .^d.0...K..UTO.h 0d 3c 4d 12 7b d8 2f ec 73 94 e3 6d b4 ff af 4d .1 Display 0x02d9e7ac background:0x00000000 LDR_OsdDisplay(13, 0x02d42200, 400, 100) Color:13 BmpAddr:0x02d42200 Width:400 Height:100 Panel 1920 x 1080 NAND load lzhs header from SysImgA(part:1) to dram(0x364dd90), size=2048 NAND_BDM_Mount: Partid=1, offset=0x40000, size=0x1e00000 [BDM] Partition: 1, Bad Block Count: 3 Decompression image to 0x00010000... NAND load image from SysImgA(part:1) to dram(0x364dd90), size=0xde886a nand read Offset exceeds total size! NANDPART_Read ASSERT2: Partition ID = 1, Offset = 0xa20000