Boot-
DRAM Channel A Calibration.
Byte 0 : Gating(1 ~ 96), Size=96, Mid=48, Set=48.
Byte 1 : Gating(1 ~ 96), Size=96, Mid=48, Set=48.
HW Byte 0 : DQS(22 ~ 50), Size 29, Set 36, HW_Set 37.
HW Byte 1 : DQS(19 ~ 47), Size 29, Set 33, HW_Set 33.
DRAM A Size = 128 Mbytes.
Boot
Start Pmain
0x00002e70
Nor boot
LZHS addr:0x00002ec0
LZHS size:0x00036550
LZHS checksum:0x00000087
Boot
Start Lmain

MT5389 Boot Loader v1.7
Boot reason: A/C power on
Read partB current flag: 0Xcf3f40,0X200,0X3.
Flash index :0,MenuID: 0xEF, DeviceID1: 0x40, DeviceID2: 0x17___________________                                                                             ________________
u4FlashSize = 0x800000___________________________________
Detect flash #0: WINBOND(W25Q64FV)______________________________________________                                                                             __________
Flash index :1,MenuID: 0xFF, DeviceID1: 0xFF, DeviceID2: 0x10___________________                                                                             ________________
u4FlashSize = 0x10000___________________________________
Detect flash #1: 512Kb________________________________________________________
vgaedid[i] = 0x0, i = 0, u4MemLen = 256.
vgaedid[i] = 0x0, i = 1, u4MemLen = 256.
vgaedid[i] = 0x0, i = 2, u4MemLen = 256.
vgaedid[i] = 0x0, i = 3, u4MemLen = 256.
vgaedid[i] = 0x0, i = 4, u4MemLen = 256.
vgaedid[i] = 0x0, i = 5, u4MemLen = 256.
vgaedid[i] = 0x0, i = 6, u4MemLen = 256.
vgaedid[i] = 0x0, i = 7, u4MemLen = 256.
vgaedid[i] = 0x0, i = 8, u4MemLen = 256.
vgaedid[i] = 0x0, i = 9, u4MemLen = 256.

Load VGA internal EDID.................
 Read partB current flag: 0Xcf3f30,0X300,0X3.
hdmiedid[i] = 0x0, i = 0, u4MemLen = 256.
hdmiedid[i] = 0x0, i = 1, u4MemLen = 256.
hdmiedid[i] = 0x0, i = 2, u4MemLen = 256.
hdmiedid[i] = 0x0, i = 3, u4MemLen = 256.
hdmiedid[i] = 0x0, i = 4, u4MemLen = 256.
hdmiedid[i] = 0x0, i = 5, u4MemLen = 256.
hdmiedid[i] = 0x0, i = 6, u4MemLen = 256.
hdmiedid[i] = 0x0, i = 7, u4MemLen = 256.
hdmiedid[i] = 0x0, i = 8, u4MemLen = 256.
hdmiedid[i] = 0x0, i = 9, u4MemLen = 256.
Load HDMI internal EDID.................
 CEC Physical offset 159
HDMI1 Physical adr 0x0
HDMI1 PA 0x0
HDMI1 checksum 0x0
HDMI2 PA 0x20
HDMI2 checksum 0xe0
HDMI1 PA 0x10
HDMI1 checksum 0xf0
pull high 1 2 3 ..............
### EEPROM read loader config failed!!!
IR DATA register : 0x       0
Boot reason: A/C power on
T8032 init A/C on case loader stage...
Load T8032 FW (addr: 0x  d2880c, size: 24576)success!!
T8032 FW version: 78
T8032 change to loader stage...
LDR_FlashCopy 0xf010 0x26180 0x80
PDWNC_SetT8032LEDBlinkOn 1___________________________
Boot reason: A/C power on
Reset Demod GPIO=e, 0->1
[PCMCIA]Set PCMCIA Access IF : SPI
VSPIHW_Init ----- Set SPI PinMux
SPI dummy delay:0x10
External CI Version : MT5135
PCMCIA Reset Demod GPIO=14, 0->1
SPI_SetPll(), spi clock: 27 Mhz
External IC Initilization done

NOR load lzhs header from:0x80000