Загрузка после подачи питания oot- DRAM Channel A Calibration. Byte 0 : DQS(11 ~ 42), Size 32, Set 24. Byte 1 : DQS(2 ~ 39), Size 38, Set 18. Byte 2 : DQS(3 ~ 38), Size 36, Set 18. Byte 3 : DQS(-1 ~ 35), Size 37, Set 15. DRAM A Size = 256 Mbytes. oot Start Pmain 0x00004000 NID=0x1d00f120 LZHS addr:0x00100040 LZHS size:0x000960a0 LZHS checksum:0x000000fb oot Start Lmain MT5365 Boot Loader v0.9 [PCMCIA]Set PCMCIA Access IF : SPI SPIHW_Init ----- Set SPI PinMux SPI dummy delay:0x10 External CI Version : MT5135 Output clock from main chip. PCMCIA Reset Demod GPIO=35, 0->1 SPI_SetPll(), spi clock: 27 Mhz External IC Initilization done MUSB none SoftReset 0x29424 = 0x01030000. MUSB pBase = 0xF0029000 init ok. MUSB none SoftReset 0x29424 = 0x01030000. MUSB pBase = 0xF002E000 init ok. Boot reason: A/C power on!!-------------use external edid, disable internal edid------------------ SIF_Master0: new design SIF_Master1: old design Boot reason: A/C power on!!T8032 init A/C on case loader stage... Load T8032 FW (addr: 0x 2d38214, size: 24576)success!! T8032 FW version: 18 T8032 change to loader stage... LDR_FlashCopy 0xf010 0x34d80 0x80 Switch NAND pinmux Detect NAND flash ID: 0x1D00F120 Detect NAND01GW3B2C NAND flash(SLC): 128MB NAND_BDM_Mount: Partid=0, offset=0x0, size=0x40000 [BDM] Partition: 0, Bad Block Count: 0 Do USB upgrade No USB device. USB upgrade stop Boot reason: A/C power on!!Boot reason: A/C power on!![PDWNC]PDWNC_TPV_DetermineNextState : u4Event = 0x6 PDWNC_TPV_DetermineNextState : u4Current = 1 PDWNC_TPV_DetermineNextState : system booting [PDWNC] Virgin Mode Status : 0x0, Offset :0x38 PDWNC_TPV_DetermineNextState : event = PDWNC_POWER_DOWN_AC_POWER Current = 0x1, Event = 0x6, Next = 0x1 Wakeup keypad array = 4 Boot reason: A/C power on!![PDWNC]PDWNC_ReadWakeupReason = 0x6 [PDWNC]Enter normal mode, LED changes to normal PDWNC_TPV_EnterNextState : u4Next = 0x1 Boot reason: A/C power on!! A_Mute GPIO=11 release AMP mute GPIO=cb release Reset Demod GPIO=23, 0->1 Display 0x02d9ebac background:0x00000000 2 bytes panel index is : 123 (0x 7b) Find panel index 123 from EEPROM [LVDS] DVOPLL init control word only [MLVDS]_u1TconMode=0x1 [MLVDS]TCLK_PCLK_RATION_NUM=0x1 [MLVDS]TCLK_PCLK_RATION_DEN=0x1 [MLVDS]u2Oclk_target=0x2bda [MLVDS]u2Oclk2_target=0x2bda [MLVDS]0x0D1a0=0xe24e820 [MLVDS]0x0D1a4=0xec8106e [LVDS] VOPLL Initialize successful ! LODFP. TG on phase 0: 0x60 No cust minilvds setting for this panel 123 tg init Tcon reg flashing 92 counts, 4 / 12 Tcon Gamma init Program Tcon Gamma dacs 0 counts, 0 / 12 TG on phase 1: 0x60 TG on phase 3: 0xffff Boot reason: A/C power on!!---------- Panel[123] PANEL_MLVDSV5GIP60_LC420WUGSCB1 1920x1080 ---------- PixelClk[Max=154000000, 60Hz=148351648, 50Hz=140625000, Min=140000000] HTotal[Max=2399, 60Hz=2199, 50Hz=2249, Min=2119] HSyncLen[60Hz=279, 50Hz=329] VTotal[Max=1379, 60Hz=1124, 50Hz=1249, Min=1090] VClk[Max=63, Min=47] HSyncWidth=30, VSyncWidth=5, HPosition60Hz=0x396, HPosition50Hz=0x3C8, VPosition=1016 LVDS_NS, LVDS_ODD_SW_OFF, DUAL_PORT, DISP_30BIT, WFB_PANEL_RESET_OFF, PWM_LOW_PANEL_BRIGHT 3D_POLARIZED Backlight[High=0x0, Middle=0x0, Low=0x0] DimFreq60Hz=120, DimFreq50Hz=100 Delay[LvdsOn=20, BacklightOn=300, BacklightOff=300, LvdsOff=20] MaxOverscan=30 Current panel setting is PANEL_MLVDSV5GIP60_LC420WUGSCB1 Backlight gpio=25, turn on value=0, LVDS gpio=16, turn on value=1 Pixel Shift=0 (1920 x 1080) LDR_OsdDisplay(13, 0x02d424c0, 400, 100) Color:13 BmpAddr:0x02d424c0 Width:400 Height:100 OSD_SetTVEOut: 1 osd flip en osd mirror en Panel 1920 x 1080 NAND load lzhs header from SysImgA(part:1) to dram(0x2fe6a00), size=2048 NAND_BDM_Mount: Partid=1, offset=0x40000, size=0x1e00000 [BDM] Partition: 1, Bad Block Count: 0 Decompression image to 0x00010000... NAND load image from SysImgA(part:1) to dram(0x2fe6a00), size=0xdf6e77 secure boot ok LZHS hardware decode start LZHS hardware decode done Starting image... Booting Nucleus Heap is at 0x012e9518(0x0ad0bf80) Main task stack is at 0x012e9528 (0x00002000) ============================================ Dram Size: 0x10000000 Memory for Image at 0x00010000(0x012d3d18): Memory Reserved for MMU at 0x006f4000(0x00004000) Memory for OSAI at 0x012eb538(0x0ad09678) Memory Reserved for ARM lib at 0x0bff96f8(0x00002908) Memory Reserved for FBM at 0x0bffc000(0x04004000) drv_init as EU model Preloader T8032 ack ! SIF_Master0: new design SIF_Master1: old design [PCMCIA]Set PCMCIA Access IF : SPI [PCMCIA]External CI Version : MT5135 [PCMCIA]External IC Initilization done [CEC]EEPROM ok. u4Val = 1. ---------------------------------TMDS361 init------------------------------------- TMDS361 is GPIO mode HDMI fast booting init... 2 bytes panel index is : 123 (0x 7b) Find panel index 123 from EEPROM TunerInit.....................EEPROM(tuner): Ofst0=0x21b,Ofst1=0xbcb,Ofst2=0x112b,def=0x69 [MUSB]USB0: Set GPIO23 = 0. [MUSB]USB1: No define vbus gpio. [MUSB]ucos MUSB SoftReset 0xF0029024 = 0x01C30000. [MUSB]ucos MUSB SoftReset 0xF002E024 = 0x01C30000. Read TunerType from EEPROM: addr(0x21b)=0x69,addr(0xbcb)=0x69,addr(0x112b)=0x69 Tuner 1 LTDIS_GetOpenFct Pair 0 done! [PCMCIA]External PCMCIA Interrupt Mode. [PC[MUSB]Set port-0 to Host mode. MCIA]MT5135 Driving Setting 8mA [PCMCIA]CI 5V Power Off ofst0=0x21b, ofst1=0xbcb, ofst2=0x112b, def=0x69 read TunerType from EEPROM, addr0[MUSB]Set port-1 to Host mode. x21b=0x69, addr0xbcb=0x69, addr0x112b=0x69 Find corresponding tuner for registration. (total 2 tuners in pool)(TunerType=0x69) Register DVB[MUSB]Set port-0 to Host mode. T Tunerall type = 105 Tuner TDTKG931D init done! [MUSB]Set port-1 to Host mode. GFX flip en GFX mirror en [NPTV]Invalid H_POS: 0x3C8 [NPTV]--> 0x800 [NPTV]Display Init[NPTV]Video SW InitZero TDC memory address Scene ID, APL, Noise Value,Bin0,Bin1,Bin2,Bin3,Bin4,Bin5,Bin6,Bin7,Bin8,Bin9,Bin10,Bin11,Bin12,Bin13,Bin14,Bin15,DS0,DS1,DS2,DS3,DS4,DS5,DS6,DS7,DS8,DS9,DS10,DS11,DS12,DS13,DS14,DS15,MoPxlRatio,MinDS,MaxDS,DSRatio,AvgDS,Noise Level,Final Confidence,MoPxl Confidence,DSRatio Confidence, [NPTV]OD use external error handling [NPTV]Load OD table [NPTV]Load OD table [NPTV]Load FB table [NPTV]Support OD [NPTV]vApiVideoInit [NAND]NAND_BDM_Mount: Partid=0, offset=0x0, size=0x40000 [NAND][BDM] Partition: 0, Bad Block Count: 0 [NAND]NAND_BDM_Mount: Partid=1, offset=0x40000, size=0x1e00000 [NAND][BDM] Partition: 1, Bad Block Count: 0 [NAND]NAND_BDM_Mount: Partid=3, offset=0x1e40000, size=0x1e00000 [NAND][BDM] Partition: 3, Bad Block Count: 1 [NAND]NAND_SDM_Mount: Partid=5, offset=0x3c40000, size=0x43c0000 [NAND][SDM] Partition: 5, Bad Block Count: 0 [NPTV]FlashPQ ID OK [NPTV]Restore Flash SmartPic Successful [NPTV]GAMMA SCRIPT=LC420WUGSCB1 [NPTV]Load OD table [NPTV]Load OD table [NPTV]Video HW Init[NPTV]VBI_Inithdmi re-init [MUSB]Set port-0 to Host mode. [MUSB]Set port-1 to Host mode. TVD MsgCtrl: NRL:60/40, PER:100/90 _bHDMIState change from HDMI_STATE_NOTREADY to HDMI_STATE_INIT _bHDMIState change from HDMI_STATE_INIT to HDMI_STATE_PWON [NPTV]Verf PE Table Passed DVBT_Initialize OK! [NPTV]FlashPQ ID OK [NPTV]QTY SCRIPT=LC420WUGSCB1 [NPTV]QTY ID OK [NPTV]Restore FlashPQ Qty successfully [NPTV]Enable AdaptiveLuma ofst0=0x21b, ofst1=0xbcb, ofst2=0x112b, def=0x69 read TunerType from EEPROM, addr0x21b=0x69, addr0xbcb=0x69, addr0x112b=0x69 Find corresponding tuner for regi_bHDMIState change from HDMI_STATE_PWON to HDMI_STATE_PWON2 stration. (total 2 tuners in pool)(TunerType=0x69) Register DVBC Tunerall type = 105 Tuner TDTKG931D init done! _bHDMIState change from HDMI_STATE_PWON2 to HDMI_STATE_SCDT DVBC_Initialize OK! Tuner 0 LTDIS_GetOpenFct Pair 1 done! ofst0=0x21b, ofst1=0xbcb, ofst2=0x112b, def=0x69 read TunerType from EEPROM, addr0x21b=0x69, addr0xbcb=0x69, addr0x112b=0x69 Find corresponding tuner for registration. (total 2 tuners in pool)(TunerType=0x69) Register ATD Tunerall type = 105 Tuner TDTKG931D init done! ATD_Initialize successful ! Read NAND Flash AQ Comm Data Success! load cdnotch code sz 80 offset 143130 0xFA7A600 load cdnotch code sz 80 offset 143130 0xFA7A600 load cdnotch code sz 80 offset 143130 0xFA7A600 Image ROBase:0x00010af0 ROLimit:0x006f8480 Protect readonly by region 1: from 0x00000000 ~ 0x00000040. MMU protect: 0x00010af0 ~ 0x006f7ffc Successed to initialize Memory Intrusion Detection! DTV>Driver Logo Disabled! OSD_SetTVEOut: 1 osd flip en osd mirror en total: 5612, avail: 3450, free: 3450 [FM](/dev/flash_sunrise_0) is mounted to (/mnt/sunr) successfully(0) total: 9188, avail: 8282, free: 8282 [FM](/dev/nand_21_0) is mounted to (/mnt/demo) successfully(0) total: 1014, avail: 802, free: 802 [FM](/dev/flash_fs_tp_0) is mounted to (/mnt/aud) successfully(0) {CI_glue}:ci_eng_init {CI_glue}- expect PROD key {CI}CI_RegInterrupt_nfy {CI_glue}- c[1] {DT} Real Time Clock is available on this system. reason: 0x00000006 - 0x00000000 wakeup reason = 6 [ACFG_CUSTOM] acfg_custom_get_svl_tsl_dual_bank ui1_g_svl_tsl_dual_bank == DUAL_BANK_SVL_TSL_INVALID and get form plf is 2 [ACFG_CUSTOM] acfg_custom_get_svl_tsl_dual_bank: default SUB {CDB} Loading metadata (version 7) {CDB} Loading metadata (version 7) {CDB} Loading metadata (version 7) {CDB} Loading metadata (version 7) [ACFG_CUSTOM] acfg_custom_get_svl_tsl_dual_bank: default SUB Align option codes (OPC_USED[NVM] - OPC1 OPC2 OPC3) 12 - 0 0 0 4 - 0 0 0 192 - 0 0 0 2 - 0 0 0 184 - 0 0 0 32 - 0 0 0 7 - 0 0 0 30 - 0 0 0 56 - 56 56 56 23 - 0 0 0 0 - 0 0 0 106 - 0 0 0 64 - 0 0 0 0 - 2 2 2 0 - 123 123 123 122 - 0 0 0 [ACFG_CUSTOM] acfg_custom_get_svl_tsl_dual_bank: default SUB [ACFG_CUSTOM] acfg_custom_get_svl_tsl_dual_bank: default SUB [a_cfg_custom_bds_update_mutirc_state] state = 0 IRRX_FilterSystemCode: set postive system code... (0)nd system code: 0 (1)nd system code: 3 (2)nd system code: 7 Pass data0 to T8032 0x0 Pass data0 to T8032 0x3 [ACFG_CUSTOM] acfg_custom_get_svl_tsl_dual_bank: default SUB [ACFG_CUSTOM] acfg_custom_get_svl_tsl_dual_bank: default SUB [BGM] a_bgm_init. FS(0x4004500) B3 = 0x4, B2 = 0x0, B1 = 0x45, B0 = 0x0 FS(0x4004500) B3 = 0x4, B2 = 0x0, B1 = 0x45, B0 = 0x0 [TCL-100426-02 i2_blue_mute = 0] FS(0x4004500) B3 = 0x4, B2 = 0x0, B1 = 0x45, B0 = 0x0 Zero TDC memory address Zero TDC memory address BGM: Power mgmt init BGM: Update scan init [BGM_OAD_DTC] _oad_detect_init [BGM_OAD_DLD] _oad_download_init BGM: Ambilight module init [BGM:] _bgm_am_power_on_evt_cb_fct reason: 0x00000006 - 0x00000000 [BGM]: Pass to continue power on [ACFG_CUSTOM] acfg_custom_get_svl_tsl_dual_bank: default SUB [ACFG_CUSTOM] acfg_custom_get_svl_tsl_dual_bank: default SUB [ACFG_CUSTOM] acfg_custom_get_svl_tsl_dual_bank: default SUB [TCL-100426-02 i2_blue_mute = 0] FS(0x4004500) B3 = 0x4, B2 = 0x0, B1 = 0x45, B0 = 0x0 FS(0x4004500) B3 = 0x4, B2 = 0x0, B1 = 0x45, B0 = 0x0 ===255 ===267 [ACFG_CUSTOM] acfg_custom_get_svl_tsl_dual_bank: default SUB [ACFG_CUSTOM] acfg_custom_get_svl_tsl_dual_bank: default SUB [CEC]CEC Driver ON -----------vHdmiSetARCOnOff(0)-------------- ------ARC off, GPIO 707 set to 1------ [AUTO_LIP_SYNC WARNING] Register the auto lip sync. [AUTO_SUBTITLE_SHIFT WARNING] register auto subtitle shift. vc_cre init vc_hiden init reason: 0x00000006 - 0x00000000 _nav_ci_info_init() call x_ci_reg_nfy()..................... FS(0x4004500) B3 = 0x4, B2 = 0x0, B1 = 0x45, B0 = 0x0 [ OAD_ACFG] a_cfg_get_oad_reminder, 0 [ OAD_ACFG] a_cfg_set_oad_reminder, 0 reason: 0x00000006 - 0x00000000 reason: 0x00000006 - 0x00000000 [!!!Return fail:nav_cec.c:nav_cec_is_amp_exist:2711:-13] [a_cfg_custom_bds_update_mutirc_state] state = 0 IRRX_FilterSystemCode: set postive system code... (0)nd system code: 0 (1)nd system code: 3 (2)nd system code: 7 Pass data0 to T8032 0x0 Pass data0 to T8032 0x3 reason: 0x00000006 - 0x00000000 [MISC] pcl wakeup reason: 6 [BGM_OAD_DTC] _oad_detect_handle_msg :13 [BGM_OAD_DLD] _oad_download_handle_msg, it will not process any message reason: 0x00000006 - 0x00000000 inpSrc[1] FS(0x4004400) B3 = 0x4, B2 = 0x0, B1 = 0x44, B0 = 0x0 ==333 {APP_TV} TV Brdcst type = 1 TV_SCART Enabled: 0 Monitor_SCART Enabled: 1 Disconnect FB at VFE disconnect FS(0x4004500) B3 = 0x4, B2 = 0x0, B1 = 0x45, B0 = 0x0 [NPTV]AdaptiveLuma: Enable Luma Histogram FS(0x4004500) B3 = 0x4, B2 = 0x0, B1 = 0x45, B0 = 0x0 reason: 0x00000006 - 0x00000000 [SYS] Version Begin =================================================== [SYS] Serial Number: REL_20131113_134318 [SYS] Version End =================================================== Watchdog enable:800001665 [ACFG_CUSTOM] acfg_custom_get_svl_tsl_dual_bank: default SUB [ACFG_CUSTOM] acfg_custom_get_svl_tsl_dual_bank: default SUB [ACFG_CUSTOM] acfg_custom_get_svl_tsl_dual_bank: default SUB [ACFG_CUSTOM] acfg_custom_get_svl_tsl_dual_bank: default SUB TunerNimTest(TunerId=1) ok(return=0) a_cfg_custom_is_Russia_model FALSE {wzd} register dt notify callback [PHM_UPG] _phm_upg_init_fct, 201012101907:TTTTTTTTTTTTTTTTTc_ci_get#CI_GET_TYPE_SLOT_NUM c_ci_get#CI_GET_TYPE_SLOT_INFO S/W Version TPM61E 2.25 NVM Version 0.07 [ACFG_CUSTOM] acfg_custom_get_svl_tsl_dual_bank: default SUB {CDB} Loading metadata (version 7) open root EDB_tuner_ter_dig_0 {EDB} _edb_dvb_load_table Ok! {CDB} Loading metadata (version 7) {CDB} Loading metadata (version 7) {CDB} Loading metadata (version 7) Open audio outport: 105 ms [MUSB]USB0: Set GPIO23 = 1. [MUSB]USB1: No define vbus gpio. FS(0x4004400) B3 = 0x4, B2 = 0x0, B1 = 0x44, B0 = 0x0 FS(0x4004500) B3 = 0x4, B2 = 0x0, B1 = 0x45, B0 = 0x0 ==333 [nav_cec_auto_sbti_sh.c:nav_cec_auto_sbti_sh_acfg_update:680:scr mode = 1,scr mode is same.] [AUTO_SUBTITLE_SHIFT WARNING] Auto subtitle shift isn't selected [nav_cec_auto_sbti_sh.c:_nav_cec_auto_sbti_sh_report_cur_viewport:402:src la = 0.] [nav_cec_auto_sbti_sh.c:_nav_cec_auto_sbti_sh_report_cur_viewport:413:src la = 0:ret = 0.] Bootup notify check time out